A Look Into The Future What Is The Fiat Panda Key Fob Replacement Industry Look Like In 10 Years

Reasons Your Fiat 500 Key Fob Won't Work

A key fob for the Fiat 500 is a convenient method to open the doors and begin the car. However, there are numerous reasons why the fob may stop working. This includes a dead coin-battery and water damage, as well as receiver modules issues, and interference.

This listing is for an NEW replacement fiat 500 key fob fiat 500x key Flip Key Remote that looks like the Ilco brand. It has to be professionally programmed (click here to search for local locksmiths in the automotive industry). Includes lock, unlock, and trunk buttons.

Dead Coin Battery

The most frequent reason that the 500 key fob won't function is a dead battery. Key fobs of today have limited operating range and must be within only a few inches from the vehicle to function. If you are further away from your vehicle, and you push the keyfob button it will not respond, and display the message "Key Fob Not Detected".

If this happens you need to replace the battery of your coin-cell (Part Number CR2032) by a fresh one of a trusted brand like Panasonic Duracell or Energizer. You can usually find them in your local hardware store or on the internet.

You can test the battery on your coin-cell by pressing the buttons while you are standing close to your Fiat 500. The car will flash its parking lights, and the key fob will operate the lock and unlock switches.

If the fob's key doesn't work after replacing the battery, it could have water damage that prevents it from connecting to the receiver module inside your vehicle. Water damage can happen in many ways, such as the simple splash or ignition submerging the key fob into saltwater at the beach. If you suspect your fob has been exposed to water, you can try placing it in a dry rice bag to pull the moisture back out. If this isn't working, you'll have to get your fob reset by an auto locksmith or a dealer.

Water Damage

While the fob has some rubber seals that keep water out of the chip's electronic circuit it, submerging it in the ocean or washing it in a machine could cause water damage. Saltwater is especially dangerous to the fob's circuit board, causing it to short out and eventually end up dying. It's not the best idea to get the fob wet however, but don't give it up even if you accidentally drop the fob in water or fail to take it out of your pants pocket.

Take the battery off first. Clean the electronic chip using isopropyl or a similar product and dry it thoroughly before replacing the battery. Test the fob afterward to verify if it's functioning. If the fob doesn't work, it may have to be programmed again. This is typically done by a professional or dealer auto locksmith.

If your key is older and not programmed to work with your vehicle You will need to replace it completely. This is an easy process that can be handled by a professional automotive locksmith. The locksmith will require the key cut to match the car's ignition. The locksmith also needs to reprogram your fob in the car's system. This is a low-cost and quick procedure that can be completed the same day.

Receiver Module Issues

One of the simplest reasons your 500 key fob could stop working is because it's out of range. The remote usually has 30 feet of range or less and if it's far from your car, it won't respond to your commands. This can be fixed by moving it closer to your vehicle until it starts responding.

If your fob does not work after replacing the battery inside the coin, which is also known as a "button", "watch" or "button" it could be due to an issue with the circuit board inside. In the majority of cases, reprogramming your fob will resolve this issue. You can find the instructions on how to do this for all automobiles by searching YouTube or consulting the owner's manual.

It is sometimes necessary to replace the metal clips that hold the coin batteries in place. If they lose tension, it can prevent the battery from being properly seated and could result in the malfunction of your remote.

In rare cases the fob can become out of alignment with your vehicle because of hardware or software problems. You can fix this issue by visiting your local auto-locksmith or dealer to reprogram your key fob. In some instances the software may require reinstallation to your body control modules.

Interference

In addition to a dead battery on a coin, the key fob may not be able to receive or transmit a signal due to interference. This is possible when the key fob is located near a radio transmitter (cell phones or radar detectors) or another source of electromagnetic radiation. Other reasons the key fob may not function include a poor connection to the buttons and internal chip, or water damage.

If your key fob suddenly stopped working, or you've tried everything at home to solve the issue (e.g. You may have a faulty 500 receiver module in the event that you've tried replacing the battery, reprogramming or using a spare key fob. The receiver module, located under the dashboard, is able to pick up radio frequency signals from your key fob. Then, it converts them into electronic commands that the vehicle interprets.

Fortunately, there's an easy way to reset every single system on board in your 500 and include the key fob. Disconnect the battery 12 volt for ignition about 15 minutes by disconnecting the negative cable first then the positive cable. Reconnect the battery. This will clear any residual electricity, and restart the computer of your car. This could help you get your key fob to function again. If the problem persists you should speak with an expert technician. They'll be able to determine the root of your problems.